Cervis TM70 Manual de Instalação Página 62
- Página / 103
- Índice
- RESOLUÇÃO DE PROBLEMAS
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
TM70/3-10 & i-Kontrol Console RC System
U035.3-TM70_Console_Sys
54
17.1 Single Master Transmitter Systems
Figure 31. Single Master Transmitter System
The Master Transmitter crane selector has options 1/1+2/2.The Slave Transmitter only has an R
release pushbutton.
When Tandem Operation Is Needed (Figure 31)
1. The operator of the Master Transmitter must have the Slave Transmitter operator RELEASE
Receiver 1. To release, the R pushbutton and the START button must by simultaneously
pressed. Transmitter 1 commands Receiver 1 to disconnect and ready itself to accept a new
ID code.
2. The operator of the Master Transmitter then selects Switch Position 1+2.
3. The operator of the Master Transmitter must press and hold the START button until the
Green LED switches ON. This commands Receiver 2 to release Receiver 2, and then new ID
codes are sent to both Receiver 1 and Receiver 2.
Both receivers 1 and 2 are then started, ready for tandem operation.
When Tandem Operation Is Finished
When tandem operation has finished, the Master Transmitter must select Switch Position 2
again (in our example above) and press the Start button. Receiver 1 is release again ready to be
used by the Slave Transmitter, and the Master Transmitter then only controls Receiver 2.
Note: To reconnect Transmitter 1 to Receiver 1 in our example above, the operator must first
cycle the transmitter — power it OFF and then ON — and then press the START button
while the selector switch in set to 1.
F2
F2
F1
F2
F2
ID1
ID2
ID2
F1
ID1
ID2
SLAVE
RECEIVER 1
RECEIVER 2
MASTER
SLAVE
- 2013 Cervis, Inc 1
- www.cervisinc.com 2
- Notes and Observations 3
- Table of Contents 4
- List of Figures 6
- List of Tables 8
- 1.1 What You MUST Do 10
- 1.2 What You MUST NOT Do 10
- 2.0 TM70 System Description 11
- 3.1 Charging Tips 14
- 4.0 Receiver 15
- 169.5mm 16
- 255.5mm 16
- 5.0 Starting Up 18
- 6.0 Operating Instructions 21
- 7.0 Maintenance 23
- 8.0 Warranty 25
- 9.0 Parts Information 25
- Recessed Philips 26
- Copy EEPROM 27
- 12.0 Change Base Channel 29
- 13.0 CANopen Interface v2.4 30
- 13.3 Bus Termination 31
- Pushbuttons 34
- Console Box 34
- 13.7 Receiver Signaling 37
- 13.8 TM70 CAN Receivers 38
- 14.0 LCD70 Display Option 41
- 14.2 Internal Connection 42
- Enter Configuration Mode 44
- 14.5 ASCII Character Map 45
- 14.6 Available Icons 46
- 14.7 VT100 Display Control 46
- Buffered Messages 47
- Example: VT100 Data Feedback 47
- 16.1 Infrared Sensor 52
- 16.2 Infrared Transmitter 53
- 16.3 Installation 54
- 16.6 Working Zone 58
- 17.0 Tandem Operation 61
- 19.0 IN0450P Option 67
- IN0450P 68
- 20.0 IN4D Option 69
- Top View 70
- 21.0 INCAN Option 72
- 22.0 A1P4RCAN Option 74
- • Polarity inversion 76
- • Curve type 76
- 23.0 A2ICAN Option 78
- 23.2 Ramp Speed 79
- 23.5 Outputs 80
- P6 Jumper 81
- P5 Jumper 81
- LR72 Connections 81
- 24.0 A2VCAN Option 82
- 24.2 Ramp Speed 83
- 24.5 A2VCAN Voltage Outputs 84
- 25.0 Tele-Alignment Option 87
- 25.2 Menu 3.1 Adjust 90
- 25.2.2 Limit Values 91
- 25.2.3 Polarity INV 91
- 25.2.4 Curve Type 91
- 25.2.5 Ramps 92
- 25.2.7 Dither 92
- 25.2.8 Reset Output 92
- 25.2.9 Troubleshooting 93
- 26.1 Detail Characteristics 94
- Option 2 95
- Option 3 96
- Option 4 97
- R70/XX Specifications 98
- 26.2 Internal Wiring 99
- 27.0 i-Kontrol Console Box 100
- U035.3-TM70_Console_Sys 102
Manuais e produtos relacionados com Controlos remotos Cervis TM70
Controlos remotos Cervis TM70 Manual de Instalação
(76 páginas)
(76 páginas)
Controlos remotos Cervis TM70 Manual do Utilizador
(49 páginas)
(49 páginas)
Controlos remotos Cervis TM70 Manual do Utilizador
(37 páginas)
(37 páginas)
BOXLIGHT CP-731i manuels
Manuels d'utilisation et guides de l'utilisateur pour Projecteurs de données BOXLIGHT CP-731i.
Nous fournissons des manuels en pdf 1 BOXLIGHT CP-731i à télécharger gratuitement par type de document : Manuel de l'utilisateur
Comentários a estes Manuais