Cervis TM70 Manual do Utilizador

SAT/TLC (01/08) TECHNICAL ASSISTANCE SERVICES ´S MANUAL TM70 PUSHBUTTON AND CONSOLE

Technical Assistance Services (01/08) 7 the contactors, and finally, place a ferrite at the power input of the receiver; see section

Technical Assistance Services (01/08) 8 indicated by the LED by green flashes at 3-second intervals. To re-activate it, the start

Technical Assistance Services (01/08) 9 Consult the section on models for the selection of the remote control. We shou

Technical Assistance Services (01/08) 10 3.3.- THE REMOTE CONTROL DOES NOTHING OR A SPECIFIC OPERATION DOES NOT WORK WHEN

Technical Assistance Services (01/08) 11 4.- INSTRUCTIONS TO REPAIR 4.1.- LISTING OF FREQUENCIES Band 433.050 – 434.790 MHz CANAL

Technical Assistance Services (01/08) 12 Band 914.150 – 915.875 MHz CANAL MHz CANAL MHz1 914,150 36 915,0252 914,175 37

Technical Assistance Services (01/08) 13 Band 869.70625 – 869.99375 MHz 4.2.-CHANGING OF BASE CHANNEL (FREQUENCY) PUSHBUTTON When

Technical Assistance Services (01/08) 14 The industrial units, as always, are installed in the plant itself and work with

Technical Assistance Services (01/08) 15 All of the parameters of a unit, working frequency, identification code, table of manoeuvre

Technical Assistance Services (01/08) 16 This is the ideal solution recommended by the IKUSI technical assistance service to users f

SAT/TLC (01/08) i I N DEX Pág. 1.- INTRODUCTION ...

Technical Assistance Services (01/08) 17 The first thing that must be checked when we have a break down is whether the LED on the

Technical Assistance Services (01/08) 18 If the green led of the button panel lights up and the unit does not work we will check the

Technical Assistance Services (01/08) 19 The industrial units, as always, are installed in the plant itself and work with

Technical Assistance Services (01/08) 20 All of the parameters of a unit, working frequency, identification code, table of manoeuvres

Technical Assistance Services (01/08) 21 This is the ideal solution recommended by the IKUSI technical assistance service to users f

Technical Assistance Services (01/08) 22 The first thing that must be checked when we have a breakdown is that the LED of the button

Technical Assistance Services (01/08) 23 The Hybrid MO70 is an optical controller with a control that can direct a maximum of 32 ste

Technical Assistance Services (01/08) 24 have one with continuous arms. We will personalize the corresponding steps electronically a

Technical Assistance Services (01/08) 25 The MO70 is an optical controller with a control that can direct a maximum of 32 steps for

Technical Assistance Services (01/08) 26 positions are for horizontal axis, the 4th,5th, and 6th positions are for vertical axis and

SAT/TLC (01/08) ii I N DEX 4.11.- MO70 HYBRID ...

Technical Assistance Services (01/08) 27 Consists of the governance of a single crane with two or more transmitters; the ID codes wi

Technical Assistance Services (01/08) 28 the button is pushed codes will determine which transmitters can work with said crane. The f

Technical Assistance Services (01/08) 29 movements simultaneously. When these bridges work simultaneously and make the same

Technical Assistance Services (01/08) 30 transmitter turns on (green Led). We can then continue working in the same mode or change

Technical Assistance Services (01/08) 31 work zone. (The LED will flash slowly in red and the buzzer will emit slow beeps). If we are

Technical Assistance Services (01/08) 32 h (m) D (m) d (m) 6 24 10 8 32 13 10 40 17 12 48 20 14 56 23 16 64 26 18 68 29 20 70 32

Technical Assistance Services (01/08) 33 5.6.- CALIBRATION OF RETURN ON DISPLAY Units wit

Technical Assistance Services (01/08) 34 5.7.- FIXED SISTEM TM70 This is a set of fixed

Technical Assistance Services (01/08) 35 5.8.- CHANGING OF BASE CHANNEL (FREQUENCY) FIXED SYSTEM TM70 When in a

Technical Assistance Services (01/08) 36 when there exist two units with the same frequency they can interfere with each other but c

SAT/TLC (01/08) iii 1.- INTRODUCTION This assistance manual is designed to facilitate the location of failures by the p

Technical Assistance Services (01/08) 37 eeprom. A receiver will only start working when it receives the signal from the transmitter

Technical Assistance Services (01/08) 38 The change of frequency must only be made when we are sure that there are two units in an i

Technical Assistance Services (01/08) 39 It is possible that for some reason, for example, the crushing of a transmitter, the eeprom

Technical Assistance Services (01/08) 40 The majority of the break downs of a remote control occur in the transmitter; it undergoes f

Technical Assistance Services (01/08) 41 The substitution of the button panel (4.4), the frequency change (4.2), the eeprom copy

Technical Assistance Services (01/08) 42 2. If the Power led lights up, check the Hard led, if the Hard led does not light up, substi

Technical Assistance Services (01/08) 43 For 48v AC power, you must put a transformer 2x24/2,4VA (195009) and put or set bridge

Technical Assistance Services (01/08) 44 To work the version of the program of the logic LE72 will be the version 1.7 or higher and t

Technical Assistance Services (01/08) 45 1. With the transmitter turned off check the power led. If it does not turn on, check the vo

Technical Assistance Services (01/08) 46 For 24v AC power, you must put a transformer 2x24/6VA (195008) and put or set bridge the res

Technical Assistance Services (01/08) 2 2.3.- BASIC OPERATION The transmitter, in addition to monitoring the battery level

Technical Assistance Services (01/08) 3 Every country has legislated certain frequency bands for the use of the different

Technical Assistance Services (01/08) 4 there are two units with the same frequency, these may interfere with each other but can neve

Technical Assistance Services (01/08) 5 In order to start the transmitter, it is necessary that all mechanisms associated wit

Technical Assistance Services (01/08) 6 Generally, these cards have no programming and to substitute it is only necessary